Instruction Guide - bZ4X, Solterra, & RZ SnapPlate
Installation
-
![Three black metal brackets arranged in a row on a white background, each with mounting holes at the corners and a central attachment area.]()
Step 1
Plate mounts are shipped in the high position by default. If you prefer a different position, follow the Plate Height Adjustment instructions ☝️ to adjust before continuing.
-
![Two hands hold a novelty California license plate with SNAPPLATE and the website everyamp.com printed on it.]()
Step 2
Install your license plate using four of the included black or silver torx security screws.
-
![A hand demonstrating the installation of a black wall mount bracket attached to a white sign, against a plain white background.]()
Step 3
Press and hold the right button to rotate the latches open.
-
![Hands attaching a SnapPlate license plate holder to a vehicle grille, showing a California license plate.]()
Step 4
Insert SnapPlate into the center of the grille and release the right button.
-
![Person attaching a removable license plate holder labeled SNAPPLATE onto a car grille.]()
Step 5
Important! Press the left button to rotate the latches closed and engage the magnets.
If the button is too difficult to fully close or the SnapPlate feels loose on the grille, adjust the latches following the Grille Depth Adjustment instructions. ☝️ -
![Close-up of a rack with black metal bars and a mounted sign. The sign is partially visible with bold text. The rack has a textured connector securing the bars.]()
Step 6
Check that the left button is flush with the body to confirm that the latches are fully closed.
-
![A person uses a screwdriver to attach a black phone holder onto a horizontal vent mount.]()
Step 7
Optionally, install a black anti-theft security screw in the hole near the right button.
Note: If the screw doesn’t reach, make sure the latches are fully closed from Step 5. -
![A person installs a Snapplate license plate holder on a vehicle grille.]()
Step 8
Don’t forget to remove SnapPlates for automated car washes. Most touchless washes are fine, but better to be on the safe side!
Plate Height Adjustment
-
![Three black metal brackets are mounted on a white background in different orientations.]()
Step 1
SnapPlates ship in the high position by default, but are adjustable into 3 possible positions.
-
![Hands using a screwdriver to assemble or adjust a black metal bracket with two vertical slots and multiple holes, set against a plain white background.]()
Step 2
Remove the two screws holding the plate mount to the body.
- For installation in the high position go to Step 3.
- For installation in the center position go to Step 4.
- For installation in the low position go to Step 5. -
![Hands using a screwdriver to attach a wall mount bracket to a black device against a white background.]()
Step 3 (High)
With the SnapPlate logo facing up, position the plate mount with the bottom two holes on the body and install screws.
- Go to Step 6
-
![Hands assembling a black metal bracket using a wrench, against a white background.]()
Step 4 (Center)
With the SnapPlate logo facing up, position the plate mount with middle holes lined up with the top or bottom holes on the base. Install screws.
- Go to Step 6
-
![Hands using a screwdriver to assemble a black metal bracket against a plain white background.]()
Step 5 (Low)
With the SnapPlate logo facing up, position the plate mount with the plate mount upside down with the holes in line with the top holes in the base. Install screws.
- Go to Step 6
-
![Hands hold a novelty California license plate reading SNAPPLATE, with everyamp.com below.]()
Step 6
If not already installed, install the license plate using four of the included black or silver security screws.
Grille Depth Adjustment
-
![Orange plastic screwdriver handle and a double-ended metal bit on a white background.]()
Step 1
Remove the T10/T25 bit from the screwdriver handle and reinstall with the T10 bit facing out.
-
![A black mechanical component with two orange circles highlighting specific areas on a white background.]()
Step 2
Locate the T10 torx screws in the center of each rotating latch.
- Go to Step 3 to loosen latches
- Go to Step 4 to tighten latches
-
![A black mechanical component with two rotating levers, marked by orange arrows, on a white background.]()
Step 3
Turn each screw counterclockwise (lefty loosey) 1/2 turn to loosen the latches by 0.25mm. Pull each latch with your fingers to make sure they are extended and then try the fit on the grille.
Repeat up to four times (two full turns) as needed.
Important! Contact support before proceeding past two turns. If loosened more than two turns, the SnapPlate could become stuck in the grille and it may be very difficult to remove. -
![A black mechanical hinge with two moveable parts and orange arrows indicating the direction of movement, set against a light gray background.]()
Step 4
Turn each screw clockwise (righty tighty) 1/2 turn to tighten the latches by 0.25mm and try the fit on the grille.
Repeat as needed.
