This page offers a step-by-step guide for installing the SnapPlate on the 2022-2023 Chevrolet Bolt EUV. Follow these instructions to ensure a secure and precise fit for your vehicle’s front plate.
Instruction Guide - 2022-2023 Chevrolet Bolt EUV
Installation Steps ➥
-
![Three black metal mounting brackets arranged on a white surface.]()
Step 1
Plate mounts are shipped in the high position by default. If you prefer a different position, follow the Plate Height Adjustment instructions ☝️ to adjust before continuing.
-
![Hands holding and installing a California license plate frame with the text SNAPPLATE and website everyamp.com.]()
Step 2
Install your license plate using four of the included black or silver torx security screws.
-
![A hand demonstrating how to slide a black, wall-mounted device in place on a white background.]()
Step 3
Press and hold the right button to rotate the latches open.
-
![Hands install a detachable front license plate holder onto a car grille. The plate reads California SNAPP PLATE.]()
Step 4
Insert SnapPlate into the center-top of the grille and release the right button.
-
![A person attaches a license plate holder labeled SNAPPLATE to a cars front grille using a clip mechanism.]()
Step 5
Important! Press the left button to rotate the latches closed and engage the magnets.
If the button is too difficult to fully close or the SnapPlate feels loose on the grille, adjust the latches following the Grille Depth Adjustment instructions. ☝️ -
![Close-up of a black metal bracket fixed to a gridded structure against a white background.]()
Step 6
Check that the left button is flush with the body to confirm that the latches are fully closed.
-
![Close-up of a person attaching a black license plate mounting bracket to a vehicle grille using a screwdriver.]()
Step 7
Optionally, install a black anti-theft security screw in the hole near the left button.
Note: If the screw doesn't reach, make sure the latches are fully closed from Step 5. -
![Hands attaching a detachable license plate holder to the front of a vehicle grille.]()
Step 8
Don't forget to remove SnapPlates for automated car washes. Most touchless washes are fine, but better to be on the safe side!
Plate Height Adjustment Steps ➥
-
![Three black metal TV wall mounts are displayed against a plain white background, each showing different angles and configurations.]()
Step 1
Bolt EUV SnapPlates ship in the high position by default, but are adjustable into 3 possible positions.
-
![Black metal bracket with a rectangular base and extended arms, featuring multiple screw holes, against a plain white background.]()
Step 2
Remove the two screws holding the plate mount to the body.
For installation in the high position go to Step 3.
For installation in the center position go to Step 4.
For installation in the low position go to Step 5. -
![A person uses a screwdriver to assemble a black metal bracket against a white background.]()
Step 3 (High)
With the SnapPlate logo on the body facing up, position the plate mount with the bottom lined up with the bottom of the body and install screws.
Go to Step 6 -
![Hand holding a black metal bracket, using a screwdriver to tighten a screw on a rectangular component attached to it.]()
Step 4 (Center)
With the SnapPlate logo on the body facing up, position the plate mount with the center holes lined up with the bottom holes of the base. Install screws.
Go to Step 6 -
![A person uses a screwdriver to assemble or adjust a black metal bracket against a plain background.]()
Step 5 (Low)
With the SnapPlate logo on the body facing up, rotate the plate mount with the top holes lined up with the top of the base. Install screws.
Go to Step 6 -
![Person installing a California license plate reading SNAPPLATE with a screwdriver, wearing a smartwatch.]()
Step 6
If not already installed, install the license plate using four of the included black or silver security screws.
Grille Depth Adjustment Steps ➥
-
![An orange screwdriver handle and a double-ended screwdriver bit on a white background.]()
Step 1
Remove the T10/T25 bit from the screwdriver handle and reinstall with the T10 bit facing out.
-
![Black mechanical device with two vertical orange-circled levers on a white background.]()
Step 2
Locate the T10 torx screw in the center of each rotating latch.
- Go to Step 3 to loosen latches
- Go to Step 4 to tighten latches
-
![Black rectangular device with two rotating levers featuring orange directional arrows, mounted on a flat surface, against a white background.]()
Step 3
Turn each screw counterclockwise (lefty loosey) 1/2 turn to loosen the latches by 0.25mm. Pull each latch with your fingers to make sure they are extended and then try the fit on the grille.
Repeat up to four times (two full turns) as needed.
Important! Contact support before proceeding past two turns. If loosened more than two turns, the SnapPlate could become stuck in the grille and it may be very difficult to remove. -
![A black mechanical device with two levers, both featuring downward-pointing orange arrows.]()
Step 4
Turn each screw clockwise (righty tighty) 1/2 turn to tighten the latches by 0.25mm and try the fit on the grille.
Repeat as needed.
