🚚 Free Shipping for US Orders Over $75

Instruction Guide - Tesla SnapPlate+

This page provides a detailed installation guide for the SnapPlate+ on Tesla Model S, 3, X, and Y. Follow the step-by-step instructions to ensure a secure fit and seamless integration with your vehicle’s design.

How to Install the SnapPlate+ on Tesla Model S, 3, X, & Y

Installation

  • Three black TV wall mount brackets in different configurations on a white background.

    Step 1

    Plate mounts are shipped in the high position by default. If you prefer a different position, follow the Plate Height Adjustment instructions ☝️ to adjust before continuing.

  • Hands are installing a license plate that reads SNAPPLATE from California, using a screwdriver. Website everyamp.com is visible below the plate number.

    Step 2

    Install your license plate using four of the included black or silver torx security screws.

  • A person holding a black rectangular device with a circular feature, under a large sign with a partially visible website address.

    Step 3

    Press the left side of the actuator to rotate the latches open.

  • Close-up of a black round object mounted on a metal grille below a vehicle license plate, with partial red website text visible.

    Step 4

    Insert into the center of the grille.

  • A hand adjusting a black circular device on a car license plate holder, with part of a website URL visible above it.

    Step 5

    Press the bottom side of the actuator to rotate it into the locked position.

    If the actuator is too difficult to fully close or the SnapPlate feels loose on the grille after it is closed, adjust the rotating latches following the Grille Depth Adjustment instructions. ☝️

  • Close-up of a black rectangular sensor mounted on a car grille, partially covered by a white license plate with black and red text.

    Step 6

    Make sure the actuator is flush with SnapPlate body to ensure it is locked in place with the magnets engaged.

  • Close-up of a person using a screwdriver to install or adjust a bracket behind a vehicles license plate.

    Step 7

    Optionally, install a black anti-theft security screw in the hole on the right side.

    Note: Take care to not overtighten the screw, it only needs to be snug to work.

  • Person attaching a black mount to a cars front grille below the license plate.

    Step 8

    Don’t forget to remove SnapPlates for automated car washes. Most touchless washes are fine, but better to be on the safe side!

Plate Height Adjustment

  • Three black metal wall brackets designed to support flat-screen televisions arranged against a white background.

    Step 1

    Tesla SnapPlates ship in the high position by default, but are adjustable into 3 possible positions for all models except for the 2021+ Model S where the extended lower bumper lip interferes with the low position. It only has high and center available.

    We recommend high for the best airflow to the grille.

  • Hands using a screwdriver to attach or adjust a black metal bracket against a white background.

    Step 2

    Remove the two screws holding the plate mount to the joint.

    - For installation in the high position go to Step 3.
    - For installation in the center position go to Step 4.
    - For installation in the low position go to Step 5.

  • Hands using a screwdriver to attach a black wall mount bracket against a white background.

    Step 3 (High)

    Position the plate mount with the bottom holes lined up with the joint and install screws.

    - Go to Step 6

  • Hands using a screwdriver to assemble or disassemble a black metal bracket against a white background.

    Step 4 (Center)

    Position the plate mount with middle holes aligned the joint. Install screws.

    - Go to Step 6

  • Hands using a screwdriver to attach a black metal bracket, shot against a plain white background.

    Step 5 (Low)

    Rotate the plate mount 180 degrees and align the holes with the joint. Install screws.

    - Go to Step 6

  • Person using an orange screwdriver to attach a custom SNAPPLATE license plate with California and everyamp.com on it.

    Step 6

    If not already installed, install the license plate using four of the included black or silver security screws.

Grille Depth Adjustment

  • An orange screwdriver handle and a double-ended metal screw bit are placed on a white background.

    Step 1

    Remove the T10/T25 bit from the screwdriver handle and reinstall with the T10 bit facing out.

  • Close-up of a black object with four cylindrical, recessed components. The cylindrical parts have orange outlines around them. The background is blurred.

    Step 2

    Locate the T10 torx screws in the center of each rotating latch.

    - Go to Step 3 to loosen latches
    - Go to Step 4 to tighten latches

  • A screwdriver tightens a screw on a black modular object with four connected sections. Orange arrows indicate the direction for each screw on the sections.

    Step 3

    Turn each screw counterclockwise (lefty loosey) 1/2 turn to loosen the latches by 0.25mm. Pull each latch with your fingers to make sure they are extended and then try the fit on the grille.

    Repeat up to four times (two full turns) as needed.

    Important: Contact support before proceeding past two turns. If loosened more than two turns, the SnapPlate could become stuck in the grille and it may be very difficult to remove.

  • A screwdriver is adjusting screws on a black device with labels and small orange arrows indicating direction.

    Step 4

    Turn each screw clockwise (righty tighty) 1/2 turn to tighten the latches by 0.25mm and try the fit on the grille.

    Repeat as needed.

Need more help?