Follow the steps below to install and adjust a SnapPlate+ front license plate mount on a 2026 Tesla Model Y Premium, Performance, or Standard or 2026 Tesla Model 3 Premium & Standard, or Performance with a bumper camera. We're here to help if you have questions or get stuck!
2026 Tesla Model Y and 3 SnapPlate+ Instruction Guide
Installation Steps ➥
-
![SnapPlate T10/T25 Screwdriver]()
Step 1
Remove the T10/T25 bit from the screwdriver handle and reinstall with the larger T25 bit facing out.
-
![A person uses a screwdriver to attach a novelty license plate reading SNAPPLATE upside down on top of a black box with automotive icons and text.]()
Step 2
Install your license plate on the plate mount using four of the included black or silver larger, washer-head torx security screws.
Note: Make sure the SNAPPLATE logo on the top of the plate mount and the license plate are both right side up. -
![Top view of a SnapPlate device labeled EVERYAMP, showing six screw locations highlighted in orange circles. The product features a black base and is branded for August, California, 2019.]()
Step 3
Use the smaller, round-head black screws to attach the bases to the plate mount in the top and bottom holes.
Note: The base with the I marker goes on the side of the plate mount with the I marker and the base with the II marker goes on the side of the plate mount with the II marker.
Optional: The plate mount can be adjusted higher by sliding the plate mount up by 1, 2, or 3 holes and installing the screws at the farthest available holes. See the plate height adjustment instructions for details ☝️ -
![A person holds a license plate mount near the front of a red vehicle, with arrows indicating alignment points and labeled open on the mounts hinges.]()
Step 4
Align the vertical openings in the bases with the vertical bars in the grille and slide the SnapPlate into the grille.
Note: You can press the OPEN buttons while installing the SnapPlate or just push it onto the grille. The OPEN buttons will move on their own. -
![A California license plate reading SNAPPLATE is mounted on a red vehicle using a detachable bracket above a front grill with “CLOSE” labels and arrows.]()
Step 5
Push the bases onto the grille while you push both CLOSE buttons to secure the SnapPlate.
Important! It should be a snug fit and there should be some resistance, but the buttons should not be difficult to push. If they're too difficult, adjust the depth following the grille depth adjustment instructions ☝️. -
![A close-up of a black plastic component attached to horizontal grill slats, with an orange circle highlighting a section on the right side.]()
Step 6
Make sure both CLOSE buttons are flush with the SnapPlate bodies to ensure they are locked in place with the magnets engaged.
-
![A screwdriver is turning a screw to attach a black plastic piece onto the front grille of a red vehicle.]()
Step 7
Optionally, tighten the black anti-theft security screws in the holes on both sides.
Note: It should take ~8 full turns to lock or unlock the screws. They do not need to be fully removed. -
![A California license plate reading SNAPPLATE is mounted on a red vehicle using a removable front plate bracket labeled OPEN with arrows pointing outward.]()
Step 8
Don't forget to remove SnapPlates for automated car washes. Most touchless washes are fine, but better to be on the safe side!
Plate Height Adjustment Steps ➥
-
![Top view of a SnapPlate device labeled EVERYAMP, showing six screw locations highlighted in orange circles. The product features a black base and is branded for August, California, 2019.]()
Step 1 (Low)
For the low position, install the bases with the four screws as marked.
-
![Black 3D-printed SnapPlate frame labeled EVERYAMP with mounting points highlighted in orange and a white blank area at the top. Box text includes AUG California SNAPPLATE EVERYAMP.COM.]()
Step 2 (Center)
For the center position, install the bases with the four screws as marked.
-
![Close-up of a SnapPlate license plate mounting bracket by EveryAmp, showing the front view with highlighted attachment points and branding details.]()
Step 3 (High)
For the high position, install the bases with the four screws as marked.
Grille Depth Adjustment Steps ➥
-
![Orange screwdriver handle and a double-ended metal screwdriver bit placed on a white background.]()
Step 1
Remove the T10/T25 bit from the screwdriver handle and reinstall with the smaller T10 bit facing out.
-
![A SnapPlate license plate mounting kit from EveryAmp is displayed on its branded packaging, showing two black plastic brackets with orange highlights.]()
Step 2
Locate the T10 torx screws in the center of each sliding latch.
- Go to Step 3 to loosen latches
- Go to Step 4 to tighten latches
-
![A SnapPlate license plate mount from EveryAmp is shown on its packaging, displaying its features as paint-safe, grille-safe, radiator-safe, and sensor-safe.]()
Step 3
Turn each screw counterclockwise (lefty loosey) 1/2 turn to loosen the latches by 0.25mm. Pull each latch with your fingers to make sure they are extended and then try the fit on the grille.
Repeat up to four times (two full turns) as needed.
Important! Contact support before proceeding past two turns. Something unusual is going on. -
![A SnapPlate license plate mount is displayed on its packaging, labeled as paint-safe, grille-safe, radiator-safe, and sensor-safe by EveryAmp.]()
Step 4
Turn each screw clockwise (righty tighty) 1/2 turn to tighten the latches by 0.25mm and try the fit on the grille.
Repeat as needed.
Video Instructions
